 |
|
|
|
|
|
|
|
|
|
|
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
|
|
|
DESCRIPTION:
SGM Bond Kote is a specially formulated two part
cementitious coating, designed to be
used as an ideal substrate to mechanically bond pool plaster
over existing plaster
finishes.
* No resurface job should be
done without this very important process!!
CHARACTERISTICS:
Superior bonding capability
High flexural strength
Eliminates excessive substrate preparation
Virtually eliminates delamination problems
Saves labor and equipment costs
Provides even dry time while plastering
|
|
LIMITATIONS:
All materials and surfaces to be coated should remain
between 40 degrees F/120
degrees F 24 hours prior and 24 hours after installation.
Do not apply in rain or extremely
high humidity. Protect "Liquid Resin" from freezing.
Plaster should be applied to Bond
Kote within 14 days or reapply Bond Kote. DO NOT USE OVER
PAINTED OR PLASTIC
FINISHES.
PACKAGING:
SGM Bond Kote is formulated in units consisting of two
65 lb. bags of a factory blended
dry cement mix and one 5 gallon container of "Liquid
Resin". These ingredients are
mixed at jobsite as per mixing instructions.
SURFACE PREPARATION:
Check completely for hollow areas and remove all loose
plaster. Remove all mildew,
algae, fungus and rust by either sand blasting or with
an acid wash which must be
followed by neutralization with soda ash. If surface is
unusually soft, painted, peeling or
flaking, then surface must be heavily sanded or water
blasted. Regardless of method
used, thoroughly wash down with "jet nozzle"
hose and let pool drain until there is no
standing water present. NOTE: Special attention is required
on pools below water table
and or leaking.
MIXING:
Make sure "liquid resin" is mechanically agitated
before use to disperse all settled solids.
Then pour "liquid resin" (5 gallon) into a clean
mixing container with flat bottom. Add
Bond Kote (two 65 lb. bags) while continuously mixing
with mechanical mixer. Continue
mixing for 2-4 minutes until Bond Kote is completely dispersed.
NEVER USE LESS
THAN 115 lbs. OF DRY MIX PER 5 GALLONS OF LIQUID RESIN.
APPLICATIONS:
To check consistency of material, apply Bond Kote with
1-1/4" nap roller onto a vertical
test area. Let material set for 1 minute; then, using
a clean textured roller, rough up
surface to desired finish. Material thickness can be adjusted
by adding a small amount of
"cement mix" if too thin or "liquid resin"
if too thick, adjust only 1 time. DO NOT
RETEMPER MIX. Once Bond Kote is mixed to correct consistency,
apply immediately,
do not let material stand unused. Apply, mixed Bond Kote
with 1-1/4" nap roller to steps
at shallow end of pool and let material set for approximately
1 minute; then, rough up
surface to desired finish with clean textured roller as
done in test area. Continue this
same process with the wall areas and then proceed to the
floor surface last. Starting at
deep end of pool make sure application is uniform in thickness
and texture.
CURING;
Minimum cure is reached in 6 hours; setting and drying
time may vary according to
atmospheric conditions. For best results wait 24 hours
before plastering.
PLASTERING:
Mist Bond Kote with clean cool water prior to plastering
to permit proper hydration. Make
sure Bond Kote is free of any foreign matter before plastering.
COVERING:
One unit covers 450-500 square feet of surface area.
CLEAN UP/STORAGE:
Clean hands, tools and containers with warm soapy water.
NOTE: USE NEW ROLLER WITH EACH APPLICATION.
|
|
Premier Swimming Pool
Renovation Corp.
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|